Gravio租赁设备设置
电池供电的设备
温度感应器
实时监控和测量温度。
了解如何设置
门窗传感器
实时检测门或窗是否打开或关闭。
了解如何设置
运动传感器
远距离检测运动。
了解如何设置
无线迷你开关
无线控制或触发连接的设备或程序。


了解如何设置
震动感应器
检测物体的运动和振动。
了解如何设置
无线双开关
无线控制或触发连接的设备或程序。
Learn how to set up
Gravio Light
使用Gravio更改此无线LED灯的颜色以指示事件或状态。
*自2019年9月中旬起租赁运输
Learn how to set up
自供电设备
温度感应器
实时监控和测量温度。
Learn how to set up
门窗传感器
实时检测门或窗是否打开或关闭。
Learn how to set up
温度感应器

产品介绍

Gravio.Aqara温湿度传感器将室内温度,湿度,大气压实时发送到Gravio。

注意:本产品仅用于室内。

快速设置

  1. 将Gravio接收器插入PC或Mac的USB端口,然后启动Gravio Edge Server。
  2. 拆下传感器的电池绝缘密封圈。
  3. 在PC,iPhone或iPad上启动Gravio Studio,点击以选择刚启动的Gravio Server,然后创建区域来描述传感器的位置以及按功能对传感器进行分组的层。 请从图层选择列表中选择“ Aqara-Temperature”。
  4. 将Graivo接收器连接到此层。
  5. 在Gravio Studio设备列表中,点击gravio Receiver行。
  6. 如果此传感器是第一个连接的传感器,请按“重置”。 (请不要在添加后续传感器之前重置接收器。)
  7. 接下来,按“配对”按钮。
  8. 进行配对时,您会看到倒数计时。 在倒数期间,按一次传感器上的按钮。
  9. 显示连接至Gravio Studio的传感器屏幕时,连接完成。

注意:如果连接失败,请将附件移近Gravio接收器,然后重试。

安装

选项1:将其直接放置在所需位置。

选项2:取下保护膜,然后将其粘贴到所需位置。

注意:保持表面清洁干燥。

技术指标

  1. 型号: WSDCGQ11LM
  2. 尺寸: 36×36×9毫米(1.42×1.42×0.35英寸)
  3. 无线协议: Zigbee
  4. 电池: CR2032
  5. 温度范围和精度: -20°〜+ 50°C,±0.3°C
  6. 湿度范围和精度: 0〜100%RH,±3%
  7. 大气压范围和精度: 30 kPa〜110 kPa,±0.12 kPa
  8. 工作湿度: 0〜95%RH,无凝结
门窗传感器

产品介绍

Aqara门/窗打开和关闭传感器检查门或窗户的打开和关闭状态。 如果传感器单元靠近磁铁,则将相应状态发送到Gravio Edge Server,在此可以触发相应的Gravio操作。

注意:本产品仅用于室内。

快速设置

  1. 将Gravio接收器插入PC或Mac的USB端口,然后启动Gravio Edge Server。
  2. 拆下传感器的电池绝缘密封圈。
  3. 在PC,iPhone或iPad上启动Gravio Studio,点击以选择刚启动的Gravio Server,然后创建区域来描述传感器的位置以及按功能对传感器进行分组的层。 请从图层选择列表中选择“ Aqara-Door”。
  4. 将Graivo接收器连接到此层。
  5. 在Gravio Studio设备列表中,点击Gravio Receiver行。
  6. 如果此传感器是第一个连接的传感器,请按“重置”。 (请不要在添加后续传感器之前重置接收器。)
  7. 接下来,在Gravio Studio中按“配对”按钮。
  8. 进行配对时,您会看到倒数计时。 在倒数期间,按一次传感器上的按钮。
  9. 显示连接至Gravio Studio的传感器屏幕时,连接完成。

注意:如果连接失败,请将附件移近Gravio接收器,然后重试。

安装

步骤1:移除保护膜。

步骤2:将标记线对准传感器单元和磁体。

步骤3:将磁铁和传感器装置粘在门窗上(建议将传感器单元安装在不动的表面上,并将磁铁安装在可动表面上。当门或窗关闭时,确保安装间隙小于22mm。)

技术指标

  1. 型号: MCCGQ11LM
  2. 尺寸: 41×22×11毫米(1.61×0.87×0.43英寸)
  3. 无线协议: Zigbee
  4. 电池: CR1632
  5. 最大检测距离: 22mm
  6. 工作温度: -10°〜+ 50°C
  7. 工作湿度: 0〜95%RH,无凝结
运动传感器

产品介绍

Aqara运动传感器使用红外线检测人体运动。 通过与Gravio链接,您可以在各种情况下使用它,例如在检测到活动或有人在场时自动打开/关闭灯。

注意:本产品仅用于室内。

快速设置

  1. 将Gravio接收器插入PC或Mac的USB端口,然后启动Gravio Edge Server。
  2. 拆下传感器的电池绝缘密封圈。
  3. 在PC,iPhone或iPad上启动Gravio Studio,点击以选择刚启动的Gravio Server,然后创建区域来描述传感器的位置以及按功能对传感器进行分组的层。 请从图层选择列表中选择“ Aqara-Occupancy”。
  4. 将Graivo接收器连接到此层。
  5. 在Gravio Studio设备列表中,点击Gravio Receiver行。
  6. 如果此传感器是第一个连接的传感器,请按“重置”。 (请不要在添加后续传感器之前重置接收器。)
  7. 接下来,在Gravio Studio中按“配对”按钮。
  8. 进行配对时,您会看到倒数计时。 在倒数期间,按一次传感器上的按钮。
  9. 显示连接至Gravio Studio的传感器屏幕时,连接完成。

注意:如果连接失败,请将附件移近Gravio接收器,然后重试。

安装

选项1:将其直接放置在所需位置。

选项2:取下保护膜,然后将其粘贴到所需位置。

选项3:将运动传感器粘贴到支架上,然后将支架粘贴到需要的位置。

注意:保持表面清洁干燥。

建议的安装高度为1.2至2.1米。 如果安装高度低于1.2米,则检测面积会减小; 如果高于2.1米,则检测区域可能有盲点。

请注意,安装时,镜头应与检测区域对齐,并尽可能靠近桌子或橱柜的边缘放置或粘贴。

技术指标

  1. 型号: RTCGQ11LM
  2. 尺寸: 30×30×33毫米(1.18×1.18×1.30英寸)
  3. 无线协议: Zigbee
  4. 电池: CR2450
  5. 最大检测距离:7
  6. 最大检测角度: 170°
  7. 工作温度: -10°〜+ 45°C
  8. 工作湿度: 0〜95%RH,无凝露
无线迷你开关

产品介绍

Aqara无线开关是紧凑型设计和低功耗的远程控制开关。 您可以将Gravio操作分配给每个操作,例如按一次,按两次或按住。

注意:本产品仅用于室内。

快速设置

  1. 将Gravio接收器插入PC或Mac的USB端口,然后启动Gravio Edge Server。
  2. 拆下传感器的电池绝缘密封圈。
  3. Start Gravio Studio on your PC, iPhone or iPad, tap to select Gravio Server which you just started, and create areas to describe where the Sensors are and layers to group them by function. Please select "Aqara-WirelessSwitch" from the layer selection list.
  4. Connect the Graivo receiver to this layer.
  5. From the Gravio Studio device list, tap the gravio Receiver line.
  6. If this sensor is the first to be connected sensor, press "Reset". (Please do not reset your receiver before adding subsequent sensors.)
  7. Next, press the "Pairing" button.
  8. When pairing is in progress, you will see a count-down. During that count-down, press the button on the sensor once.
  9. When the sensor connected to Gravio Studio screen is displayed, connection is completed.

Note: If the connection fails, please move the accessory closer to the Gravio Receiver and try again.

Installation

Option 1: Place it directly in the desired position.

Option 2 : Remove the protective film, and stick the wireless button to the desired position.

* Keep the surface clean and dry.

Specifications

  1. Model: WXKG11LM
  2. Dimensions: 45 × 45 × 12 mm (1.77 × 1.77 × 0.47 in. )
  3. Wireless Protocol: Zigbee
  4. Battery: CR2032
  5. Operating Temperature: -10° ~ +50° C
  6. Operating Humidity: 0~95% RH, no condensation
Vibration Sensor

Product introduction

The Aqara Vibration Sensor is embedded with a high precision acceleration sensor and it detects the vibration and movement of objects. It also works with other smart accessories to set various smart scenes, such as, local and remote alarm when it detects glass breaks.

Note: This product is for indoor use only.

Quick Setup

  1. Insert the Gravio receiver in the USB port of your PC or Mac, then start the Gravio Edge Server.
  2. Remove the sensor's battery insulation seal.
  3. Start Gravio Studio on your PC, iPhone or iPad, tap to select Gravio Server which you just started, and create areas to describe where the Sensors are and layers to group them by function. Please select "Aqara-Vibration-Falling",  "Aqara-Vibration-Inclination" or  "Aqara-Vibration-Stable" from the layer selection list.
  4. Connect the Graivo receiver to this layer.
  5. From the Gravio Studio device list, tap the gravio Receiver line.
  6. If this sensor is the first to be connected sensor, press "Reset". (Please do not reset your receiver before adding subsequent sensors.)
  7. Next, press the "Pairing" button.
  8. When pairing is in progress, you will see a count-down. During that count-down, press the button on the sensor once.
  9. When the sensor connected to Gravio Studio screen is displayed, connection is completed.

Note: If the connection fails, please move the accessory closer to the Gravio Receiver and try again.

Installation

Option 1: Place it directly in the desired position.

Option 2 : Remove the protective film, and stick the wireless button to the desired position.

* Keep the surface clean and dry.

Specifications

  1. Model: DJT11LM
  2. Dimensions: 36 × 36 × 9 mm (1.42 × 1.42 × 0.35 in. )
  3. Wireless Protocol: Zigbee
  4. Battery: CR2032
  5. Operating Temperature: -10° ~ +50° C
  6. Operating Humidity: 0~95% RH, no condensation
Wireless Double Switch

Product introduction

The Aqara wireless switch is a compact design and low power consumption remote control switch. You can assign Gravio action to each operation such as press once, press twice, or press and hold.

Note: This product is for indoor use only.

Quick Setup

  1. Insert the Gravio receiver in the USB port of your PC or Mac, then start the Gravio Edge Server.
  2. Remove the sensor's battery insulation seal.
  3. Start Gravio Studio on your PC, iPhone or iPad, tap to select Gravio Server which you just started, and create areas to describe where the Sensors are and layers to group them by function. Please select "Aqara-WirelessSwitch" from the layer selection list.
  4. Connect the Graivo receiver to this layer.
  5. From the Gravio Studio device list, tap the gravio Receiver line.
  6. If this sensor is the first to be connected sensor, press "Reset". (Please do not reset your receiver before adding subsequent sensors.)
  7. Next, press the "Pairing" button.
  8. When pairing is in progress, you will see a count-down. During that count-down, press the button on the sensor once.
  9. When the sensor connected to Gravio Studio screen is displayed, connection is completed.

Note: If the connection fails, please move the accessory closer to the Gravio Receiver and try again.

Installation

Option 1: Place it directly in the desired position.

Option 2 : Remove the protective film, and stick the wireless button to the desired position.

* Keep the surface clean and dry.

Specifications

  1. Model: WXKG11LM
  2. Dimensions: 45 × 45 × 12 mm (1.77 × 1.77 × 0.47 in. )
  3. Wireless Protocol: Zigbee
  4. Battery: CR2032
  5. Operating Temperature: -10° ~ +50° C
  6. Operating Humidity: 0~95% RH, no condensation
Gravio Light

Product introduction

The Aqara wireless switch is a compact design and low power consumption remote control switch. You can assign Gravio action to each operation such as press once, press twice, or press and hold.

Note: This product is for indoor use only.

Quick Setup

  1. Insert the Gravio receiver in the USB port of your PC or Mac, then start the Gravio Edge Server.
  2. Remove the sensor's battery insulation seal.
  3. Start Gravio Studio on your PC, iPhone or iPad, tap to select Gravio Server which you just started, and create areas to describe where the Sensors are and layers to group them by function. Please select "Aqara-WirelessSwitch" from the layer selection list.
  4. Connect the Graivo receiver to this layer.
  5. From the Gravio Studio device list, tap the gravio Receiver line.
  6. If this sensor is the first to be connected sensor, press "Reset". (Please do not reset your receiver before adding subsequent sensors.)
  7. Next, press the "Pairing" button.
  8. When pairing is in progress, you will see a count-down. During that count-down, press the button on the sensor once.
  9. When the sensor connected to Gravio Studio screen is displayed, connection is completed.

Note: If the connection fails, please move the accessory closer to the Gravio Receiver and try again.

Installation

Option 1: Place it directly in the desired position.

Option 2 : Remove the protective film, and stick the wireless button to the desired position.

* Keep the surface clean and dry.

Specifications

  1. Model: WXKG11LM
  2. Dimensions: 45 × 45 × 12 mm (1.77 × 1.77 × 0.47 in. )
  3. Wireless Protocol: Zigbee
  4. Battery: CR2032
  5. Operating Temperature: -10° ~ +50° C
  6. Operating Humidity: 0~95% RH, no condensation